Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of RADITER B RVA150 100 NT - (PBT+ASA)-GF15 - RadiciGroup High Performance Polymers

Check here, which other Raditer B RVA datasheets, application examples or technical articles are available in Material Data Center

Processing/Physical Characteristics - Mechanical properties - Thermal properties - Electrical properties - Other properties - Diagrams

Any use of this information falls under the rules of our disclaimer.

Product Texts

PBT/ASA blend, 15% glass fibre reinforced injection moulding grade. Natural colour.

Suitable for parts requiring medium stiffness and improved mechanical resistance, reduced shrinkage and low warpage. Good surface aspect.

Processing/Physical Characteristics	Value	Unit	Test Standard
ISO Data
Molding shrinkage, parallel	0.4	%	ISO 294-4, 2577
Molding shrinkage, normal	0.6	%	ISO 294-4, 2577

Mechanical properties	Value	Unit	Test Standard
ISO Data
Tensile Modulus	5600	MPa	ISO 527
Stress at break	105	MPa	ISO 527
Strain at break	3.3	%	ISO 527
Charpy impact strength, +23°C	60	kJ/m²	ISO 179/1eU
Charpy notched impact strength, +23°C	7	kJ/m²	ISO 179/1eA

Thermal properties	Value	Unit	Test Standard
ISO Data
Melting temperature, 10°C/min	222	°C	ISO 11357-1/-3
Temp. of deflection under load, 1.80 MPa	145	°C	ISO 75-1/-2
Burning Behav. at thickness h	HB	class	IEC 60695-11-10
Thickness tested	1.6	mm	-

Electrical properties	Value	Unit	Test Standard
ISO Data
Volume resistivity	1E13	Ohm*m	IEC 62631-3-1

Other properties	Value	Unit	Test Standard
Density	1340	kg/m³	ISO 1183

Diagrams

Characteristics

Processing

Injection Molding

Delivery form

Granules, Natural Color

Additives

Release agent

Features

Low Warpage

Regional Availability

North America, Europe, Asia Pacific, South and Central America, Near East/Africa

Other text information

Injection molding

The material is delivered in moisture-proof packaging. It is important to dry the material prior to processing: maximum recommended water content is 0.02%. Typical conditions with a desiccant drier: temperature 120 ° C, dew point -40 ° C or below, time 2-4 h or more. Special care must be taken to avoid moisture absorption and contamination with other polymers when adding regrind material. Colour variation and mechanical properties reduction may occur and should always be carefully monitored.

Injection Molding Processing Parameters

Melt Temperature	Mold Temperature	Injection Speed
250 - 280°C	80 - 90°C	medium-high

Disclaimer

Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.

Created: Source: www.materialdatacenter.com

Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.